Products+
155Mbps 1550nm 120km DFB LC compatible SFP Optical Transceiver
155Mbps 1550nm 120km DFB SFP Optical Transceiver, fully tested compatible for over 100 vendors.
Features
* Data-rate of 155Mbps operation
* DFB 1550nm wavelengths laser and PIN photodetector for 120km transmission
* Compliant with SFP MSA and SFF-8472 with duplex LC receptacle
* Digital Diagnostic Monitoring:
Internal Calibration or External Calibration
* Compatible with RoHS
* +3.3V single power supply
* Operating case temperature:
Standard : 0 to +70°C
Industrial : -40 to +85°C
Applications
* Gigabit Ethernet
* Fiber Channel
* Switch to Switch interface
* Switched backplane applications
* Router/Server interface
* Other optical transmission systems
Description
The SFP transceivers are high performance, cost effective modules supporting data-rate of 155Mbps and 120km transmission distance with SMF.
The transceiver consists of three sections: a uncooled DFB laser transmitter, a PIN photodiode integrated with a trans-impedance preamplifier (TIA) and MCU control unit. All modules satisfy class I laser safety requirements.
The transceivers are compatible with SFP Multi-Source Agreement (MSA) and SFF-8472. For further information, please refer to SFP MSA.
Absolute Maximum Ratings
Table 1 - Absolute Maximum Ratings
Parameter |
Symbol |
Min |
Max |
Unit |
Supply Voltage |
Vcc |
-0.5 |
4.5 |
V |
Storage Temperature |
Ts |
-40 |
+85 |
°C |
Operating Humidity |
- |
5 |
95 |
% |
Recommended Operating Conditions
Table 2 - Recommended Operating Conditions
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
|
Operating Case Temperature |
Standard |
Tc |
0 |
|
+70 |
°C |
Power Supply Voltage |
Vcc |
3.13 |
3.3 |
3.47 |
V |
|
Power Supply Current |
Icc |
|
|
300 |
mA |
|
Data Rate |
|
|
155 |
|
Mbps |
|
Optical and Electrical Characteristics
Table 4 - Optical and Electrical Characteristics
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
Notes |
||
Transmitter |
||||||||
Centre Wavelength |
λc |
1520 |
1550 |
1580 |
nm |
|
||
Spectral Width (-20dB) |
∆λ |
|
|
1 |
nm |
|
||
Side Mode Suppression Ratio |
SMSR |
30 |
|
|
dB |
|
||
Average Output Power |
Pout |
0 |
|
5 |
dBm |
1 |
||
Extinction Ratio |
ER |
10 |
|
|
dB |
|
||
Jitter Generation (RMS) |
|
|
|
0.01 |
UI |
|
||
Jitter Generation (PK-PK) |
|
|
|
0.1 |
UI |
|
||
Output Optical Eye |
Compliant Telcordia GR-253-CORE and ITU-T G.957 |
|
||||||
Optical Rise/Fall Time (20%~80%) |
tr/tf |
|
|
0.26 |
ns |
|
||
Data Input Swing Differential |
VIN |
300 |
|
1860 |
mV |
2 |
||
Input Differential Impedance |
ZIN |
90 |
100 |
110 |
Ω |
|
||
TX Disable |
Disable |
|
2.0 |
|
Vcc |
V |
|
|
Enable |
|
0 |
|
0.8 |
V |
|
||
TX Fault |
Fault |
|
2.0 |
|
Vcc |
V |
|
|
Normal |
|
0 |
|
0.8 |
V |
|
||
Receiver |
||||||||
Centre Wavelength |
λc |
1260 |
|
1580 |
nm |
|
||
Receiver Sensitivity |
|
|
|
-34 |
dBm |
3 |
||
Receiver Overload |
|
-9 |
|
|
dBm |
3 |
||
LOS De-Assert |
LOSD |
|
|
-38 |
dBm |
|
||
LOS Assert |
LOSA |
-45 |
|
|
dBm |
|
||
LOS Hysteresis |
|
1 |
|
4 |
dB |
|
||
Data Output Swing Differential |
Vout |
370 |
|
1800 |
mV |
4 |
||
LOS |
High |
2.0 |
|
Vcc |
V |
|
||
Low |
0 |
|
0.8 |
V |
|
|||
Notes:
- The optical power is launched into SMF.
- PECL input, internally AC-coupled and terminated.
- Measured with a PRBS 223-1 test pattern @155Mbps, BER ≤1×10-12.
- Internally AC-coupled.
Timing and Electrical
Table 5 - Timing and Electrical
Parameter |
Symbol |
Min |
Typical |
Max |
Unit |
Tx Disable Negate Time |
t_on |
|
|
1 |
ms |
Tx Disable Assert Time |
t_off |
|
|
10 |
µs |
Time To Initialize, including Reset of Tx Fault |
t_init |
|
|
300 |
ms |
Tx Fault Assert Time |
t_fault |
|
|
100 |
µs |
Tx Disable To Reset |
t_reset |
10 |
|
|
µs |
LOS Assert Time |
t_loss_on |
|
|
100 |
µs |
LOS De-assert Time |
t_loss_off |
|
|
100 |
µs |
Serial ID Clock Rate |
f_serial_clock |
|
|
400 |
KHz |
MOD_DEF (0:2)-High |
VH |
2 |
|
Vcc |
V |
MOD_DEF (0:2)-Low |
VL |
|
|
0.8 |
V |
EEPROM Information
The SFP MSA defines a 256-byte memory map in EEPROM describing the transceiver’s capabilities, standard interfaces, manufacturer, and other information, which is accessible over a 2 wire serial interface at the 8-bit address 1010000X (A0h). The memory contents refer to Table 6.
Table 6 - EEPROM Serial ID Memory Contents (A0h)
Addr. |
Field Size (Bytes) |
Name of Field |
Hex |
Description |
0 |
1 |
Identifier |
03 |
SFP |
1 |
1 |
Ext. Identifier |
04 |
MOD4 |
2 |
1 |
Connector |
07 |
LC |
3—10 |
8 |
Transceiver |
00 08 04 00 00 00 00 00 |
OC-3,Single mode long reach |
11 |
1 |
Encoding |
03 |
NRZ |
12 |
1 |
BR, nominal |
02 |
155Mbps |
13 |
1 |
Reserved |
00 |
|
14 |
1 |
Length (9um)-km |
78 |
120km |
15 |
1 |
Length (9um) |
FF |
120km |
16 |
1 |
Length (50um) |
00 |
|
17 |
1 |
Length (62.5um) |
00 |
|
18 |
1 |
Length (copper) |
00 |
|
19 |
1 |
Reserved |
00 |
|
20—35 |
16 |
Vendor name |
47 69 67 61 BT 69 67 68 74 20 20 20 20 20 20 20 |
"BTON"(ASCⅡ) |
36 |
1 |
Reserved |
00 |
|
37—39 |
3 |
Vendor OUI |
00 00 00 |
|
40—55 |
16 |
Vendor PN |
47 50 2D 35 35 30 33 2D 31 32 43 44 20 20 20 20 |
“BT-OC3-120D ”(ASCⅡ) |
56—59 |
4 |
Vendor rev |
xx xx xx xx |
xx.xx revision (ASCⅡ) |
60-61 |
2 |
Wavelength |
0A AA |
1550nm |
62 |
1 |
Reserved |
00 |
|
63 |
1 |
CC BASE |
xx |
Check sum of bytes 0 - 62 |
64—65 |
2 |
Options |
00 1A |
LOS,TX_FAULT and TX_DISABLE |
66 |
1 |
BR, max |
00 |
|
67 |
1 |
BR, min |
00 |
|
68—83 |
16 |
Vendor SN |
xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx xx |
ASCⅡ |
84—91 |
8 |
Vendor date code |
xx xx xx xx xx xx 20 20 |
Year(2 bytes),Month(2 bytes),Day(2 bytes) |
92 |
1 |
Diagnostic type |
xx |
Diagnostics |
93 |
1 |
Enhanced option |
80 |
Diagnostics(Optional Alarm/warning flags) |
94 |
1 |
SFF-8472 |
01 |
Diagnostics(SFF-8472 Rev 9.3) |
95 |
1 |
CC EXT |
xx |
Check sum of bytes 64 - 94 |
96—255 |
160 |
|
|
|
Mechanical Dimensions