Products+

    10G SFP+ Passive High Speed Cable

    10G SFP+ Compatible Direct Attach Copper Twinax Passive Cable

    10G SFP+ Compatible Direct Attach Copper Twinax Passive Cable, fully tested compatible for over 100 vendors.
    Compatible Device: Cisco SFP-H10GB-CU2M, Cisco SFP-H10GB-CU5M, Cisco SFP-H10GB-ACU7M, Cisco SFP-H10GB-CU3M

     Features:
    • Compliant to SFP+ Multi Source Agreement SFF-8432
    • Compliant with IEEE 802.3ae
    • Optimized NEXT & Return Loss
    • Enhanced EMI / EMC performance
    • Supports serial ID functionality thru EEPROM
    • Passive cable assembly supports distances up to 10 meters
    • 30AWG to 24AWG cable sizes available
    • RoHS compliant and Halogen-Free option available

    • Applications :
    • 1-8G Fiber Channel and 1-10G Gigabit Ethernet
    • Hub, Switches, Routers, Servers, Network Interface Card(NICs)
    • Data center cabling infrastructure
    • Networking, Storage, Telecommunications

     

     

    • (Outline drawing):

     

    • Wiring Diagram

     

     

     

    • Electrical Performance
      • Signal Integrity

     

    ITEM

    REQUIREMENT

    TEST CONDITION

    Differential Impedance

    Cable Impedance

    105+5/-5Ω

    Rise time of 35ps

    (20 % - 80 %).

     

    Paddle Card Impedance

    100±10Ω

    Cable Termination Impedance

    100±15Ω

    [Differential (Input/Output)Return loss SDD11/SDD22]

    Return loss(f)

     

    Where

    f              is the frequency in GHz

    Return loss(f)  is the return loss at frequency f

    0.01GHz≤f≤11.1GHz

    SFF-8431 Rev.4.1

    [Differential Insertion Loss (SDD21  Max.)]

     

    (Differential Insertion Loss Max.)

    0.01GHz≤f≤11.1GHz

              F

    AWG

    600MHz

    1.25GHz

    2.5GHz

    5.0GHz

    30(1m)Max

    2.5dB

    3.5dB

    4.5dB

    6.5dB

    30(2m)Max

    3.8dB

    5.3dB

    6.8dB

    9.8dB

    30(3m)Max

    5.0dB

    7.0dB

    9.0dB

    13.0dB

    26(5m)Max

    5.5dB

    7.0dB

    10.5dB

    15.0dB

    24(10m)Max

    7.0dB

    10.0dB

    14.0dB

    20.0dB

     

    [MDNEXT(multiple disturber

    near-end crosstalk)]

    26dB @5GHz

    0.01GHz≤f≤11.1GHz

    [Insertion Loss Deviation]

    -0.7-0.2*10-3f ≤ ILD ≤ 0.7+0.2*10-3f

    (f is the frequency in MHz)

    0.01GHz≤f≤5.0GHz

     

     

     

     

    6.2 Other Electrical Performance

    ITEM

    REQUIREMENT

    TEST CONDITON

    [Low Level Contact Resistance]

    70milliohms Max. From initial.

    EIA-364-23:Apply a maximum voltage of 20mV

    And a current of 100 mA.

    Insulation Resistance

    10Mohm(Min.)

    EIA364-21:AC 300V 1minute

     [Dielectric Withstanding Voltage]

    DC 500V 1 minute disruptive discharge.

    EIA-364-20:Apply a voltage

    of 500 VDC for 1minute

    between adjacent terminals

    And between adjacent terminals and ground.

     

     

    • Environment Performance

    ITEM

    REQUIREMENT

    TEST CONDITON

    [Operating Temp. Range]

    -20°C to +75°C

    Cable operating temperature range.

    Storage Temp. Range

    (in packed condition)]

    -20°C to +55°C

    Cable storage temperature range

    in packed condition.

    [Thermal Cycling Non-Powered]

    No evidence of physical damage

    EIA-364-32D, Method A, -25 to 90C, 100 cycles, 15 min. dwells

    [Salt Spraying]

    48 hours salt spraying after shell

    corrosive area less than 5.

    EIA-364-26

    Mixed Flowing Gas

    Pass electrical tests per 3.1 after

    stressing. (For connector only)

    EIA-364-35 Class II,14 days.

    Temp. Life

    No evidence of physical damage

    EIA-364-17C w/ RH, Damp heat 90 at 85% RH for 500 hours then return to ambient

    Cable Cold Bend

    4H,No evidence of physical damage

    Condition: -20±2, mandrel diameter is 6 times the cable diameter.

     

     

     

     

    • Mechanical and Physical Characteristics

    ITEM

    REQUIREMENT

    TEST CONDITON

    Vibration

    Pass electrical tests

    per 3.1 after stressing.

    Clamp & vibrate per EIA-364-28E,

    TC-VII, test condition letter – D, 15 minutes in X, Y & Z axis.

    Cable Flex

    No evidence of physical damage

    Flex cable 180° for 20 cycles (±90° from nominal position) at 12 cycles per minute with a 1.0kg load applied to the cable jacket. Flex in the boot area 90º in each direction from vertical. Per EIA-364-41C

    Cable Plug Retention in Cage

    90N Min.

    No evidence of physical damage

    Pull on cable jacket approximately 1 ft behind cable plug. No functional damage to cable plug below 90N.

    Per SFF-8432 Rev 5.0

    Cable Retention in Plug

    90N Min.

    No evidence of physical damage

    Cable plug is fixtured with the bulk cable hanging vertically. A 90N axial load is applied (gradually) to the cable jacket and held for 1 minute. Per EIA-364-38B

    Mechanical Shock

    Pass electrical tests

    Per 3.1 after stressing.

    Clamp and shock per EIA-364-27B, TC-G,3 times in 6 directions, 100g, 6ms.

    Cable Plug Insertion

    18N Max.(SFP28)

    Per SFF-8432 Rev 5.0

    Cable plug Extraction

    12.5N Max. (SFP28)

    Measure without the aid of any cage kick-out springs. Place axial load on de-latch to de-latch plug. Per SFF-8432 Rev 5.0

    Durability

    50 cycles,No evidence of physical damage

    EIA-364-09, perform plug &unplug cycles:Plug and receptacle mate rate: 250times/hour. 50times for module (CONNECTOR TO PCB)

     

     

     

     

     

    9 Supported Versions

    PN

    Description

    10G-PDAC-SFP-0.5

    Multi-Vendor Compatible 10G SFP+  to SFP+ Twinax Passive Copper Cable(1.0625-10.52 Gbps, Max. 0.5m, AWG 30, Temp. 0-70C)

    10G-PDAC-SFP-0.65

    Multi-Vendor Compatible 10G SFP+  to SFP+ Twinax Passive Copper Cable(1.0625-10.52 Gbps, Max. 0.65m, AWG 30, Temp. 0-70C)

    10G-PDAC-SFP-1

    Multi-Vendor Compatible 10G SFP+  to SFP+ Twinax Passive Copper Cable(1.0625-10.52 Gbps, Max. 1m, AWG 30, Temp. 0-70C)

    10G-PDAC-SFP-1.2

    Multi-Vendor Compatible 10G SFP+  to SFP+ Twinax Passive Copper Cable(1.0625-10.52 Gbps, Max. 1.2m, AWG 30, Temp. 0-70C)

    10G-PDAC-SFP-1.5

    Multi-Vendor Compatible 10G SFP+  to SFP+ Twinax Passive Copper Cable(1.0625-10.52 Gbps, Max. 1.5m, AWG 30, Temp. 0-70C)

    10G-PDAC-SFP-2

    Multi-Vendor Compatible 10G SFP+  to SFP+ Twinax Passive Copper Cable(1.0625-10.52 Gbps, Max. 2m, AWG 30, Temp. 0-70C)

    10G-PDAC-SFP-2.5

    Multi-Vendor Compatible 10G SFP+  to SFP+ Twinax Passive Copper Cable(1.0625-10.52 Gbps, Max. 2.5m, AWG 30, Temp. 0-70C)

    10G-PDAC-SFP-3

    Multi-Vendor Compatible 10G SFP+  to SFP+ Twinax Passive Copper Cable(1.0625-10.52 Gbps, Max. 3m, AWG 30, Temp. 0-70C)

    10G-PDAC-SFP-4

    Multi-Vendor Compatible 10G SFP+  to SFP+ Twinax Passive Copper Cable(1.0625-10.52 Gbps, Max. 4m, AWG 28, Temp. 0-70C)

    10G-PDAC-SFP-5

    Multi-Vendor Compatible 10G SFP+  to SFP+ Twinax Passive Copper Cable(1.0625-10.52 Gbps, Max. 5m, AWG 26, Temp. 0-70C)

    10G-PDAC-SFP-6

    Multi-Vendor Compatible 10G SFP+  to SFP+ Twinax Passive Copper Cable(1.0625-10.52 Gbps, Max. 6m, AWG 24, Temp. 0-70C)

    10G-PDAC-SFP-7

    Multi-Vendor Compatible 10G SFP+  to SFP+ Twinax Passive Copper Cable(1.0625-10.52 Gbps, Max. 7m, AWG 24, Temp. 0-70C)

    10G-PDAC-SFP-10

    Multi-Vendor Compatible 10G SFP+  to SFP+ Twinax Passive Copper Cable(1.0625-10.52 Gbps, Max. 10m, AWG 24, Temp. 0-70C)

     

     

     

     

     

     

     

     

    10 Revision  record:

     

    Date

    version

    change Description

    Author

    2017-05-19

    V0

    First release

    LEON

    2017-08-17

    V1.0

    Add performance metrics

     

    LEON

     

     

    Send Message

    • Transceivers
    • Cables
    • About us
    • Contact